ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES FOR PETROLEUM REFINING INTRODUCTION 1. The Environmental, Health, and Safety (EHS) Guidelines are technical reference documents with general and industry-specific examples of Good International Industry Practice (GIIP).1 When one or more members of the World Bank Group are involved in a project, these EHS Guidelines are applied as required by their respective policies and standards. These industry sector EHS Guidelines are designed to be used together with the General EHS Guidelines document, which provides guidance to users on common EHS issues potentially applicable to all industry sectors. For complex projects, use of multiple industry sector guidelines may be necessary. A complete list of industry sector guidelines can be found at: www.ifc.org/ehsguidelines. 2. The EHS Guidelines contain the performance levels and measures that are generally considered to be achievable in new facilities by existing technology at reasonable costs. Application of the EHS Guidelines to existing facilities may involve the establishment of site-specific targets, with an appropriate timetable for achieving them. 3. The applicability of the EHS Guidelines should be tailored to the hazards and risks established for each project on the basis of the results of an environmental assessment in which site-specific variables— such as host country context, assimilative capacity of the environment, and other project factors —are taken into account. The applicability of specific technical recommendations should be based on the professional opinion of qualified and experienced persons. 4. When host country regulations differ from the levels and measures presented in the EHS Guidelines, projects are expected to achieve whichever is more stringent. If less stringent levels or measures than those provided in these EHS Guidelines are appropriate, in view of specific project circumstances, a full and detailed justification for any proposed alternatives is needed as part of the site-specific environmental assessment. This justification should demonstrate that the choice for any alternate performance levels is protective of human health and the environment. APPLICABILITY 5. The EHS Guidelines for Petroleum Refining cover processing operations from raw crude oil to finished products, for example refinery fuel gas, liquefied petroleum gas (LPG), motor gasoline (Mo-Gas), kerosene, diesel oil, heating oil, fuel oil, bitumen, asphalt, lubricant oils, waxes, sulfur, pet-coke, and intermediate products (e.g., propane/propylene mixtures, virgin naphtha, middle distillate and vacuum distillate, aromatics) for the petrochemical industry. Annex A contains a description of industry activities. 1 Defined as the exercise of professional skill, diligence, prudence and foresight that would be reasonably expected from skilled and experienced professionals engaged in the same type of undertaking under the same or similar circumstances globally. The circumstances that skilled and experienced professionals may find when evaluating the range of pollution prevention and control techniques available to a project may include, but are not limited to, varying levels of environmental degradation and environmental assimilative capacity, as well as varying levels of financial and technical feasibility. 1 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 Further information on EHS issues related to storage tank farms is provided in the EHS Guidelines for Crude Oil and Petroleum Product Terminals. This document is organized in the following manner: 1. Industry-Specific Impacts and Management ............................................................................. 2 1.1 Environment ............................................................................................................................. 2 1.2 Occupational Health and Safety ............................................................................................ 13 1.3 Community Health and Safety ............................................................................................... 17 2. Performance Indicators Monitoring ......................................................................................... 18 2.1 Environment ........................................................................................................................... 18 2.2 Occupational Health and Safety ............................................................................................ 21 3. References ................................................................................................................................. 23 Annex A. General Description of Petroleum Industry Activities ................................................. 26 1. INDUSTRY-SPECIFIC IMPACTS AND MANAGEMENT 6. The following section provides a summary of the EHS issues that may arise during the operational phase of petroleum refining, along with recommendations for their management. Recommendations for the management of EHS issues common to most large industrial facilities during the construction and decommissioning phases are provided in the General EHS Guidelines. 1.1 Environment 7. Environmental issues associated with petroleum refining include the following:  Emissions to atmosphere;  Handling and disposal of process wastewater (storage, transportation, and treatment);  Handling of hazardous materials and wastes; and  Noise from operating machinery. Emissions to Atmosphere Flue Gases 8. Flue gas emissions to the atmosphere of carbon dioxide (CO 2), nitrogen oxides (NOx), sulfur oxides (SOx), carbon monoxide (CO), and particulate matter (PM) in the petroleum refining sector result from the combustion of gas and oil in gas turbines, boilers, engines, and process heaters for power, steam, and heat generation. Flue gas can also be emitted from waste heat boilers associated with some process units during continuous catalyst regeneration (CCR) or fluid petroleum coke combustion. For example, flue gas is emitted from the stack to the atmosphere in the Bitumen Blowing Unit (BBU), from the catalyst regenerator in both the Fluid Catalytic Cracking Unit (FCCU) and the Residue Catalytic Cracking Unit (RCCU), and in the sulfur recovery unit (SRU), possibly also containing small amounts of SOx and hydrogen sulfide (H2S). 2 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 9. Guidance for the management of small combustion source emissions with a capacity of up to 50 megawatt thermal (MWth), including air emission standards for exhaust emissions, is provided in the General EHS Guidelines. For combustion source emissions such as boilers, engines, and turbines with a capacity greater than 50 MWth, refer to the EHS Guidelines for Thermal Power Plants. 10. For process heaters, the following primary pollution prevention and control measures should be considered:  Installation of combustion air preheaters, to increase furnace efficiency;  Optimization of furnace operations, and hence combustion efficiency, by continuous monitoring and advanced control of the operations variables (temperature and oxygen concentration of flue gas for combustion optimization air/fuel ratio for the fuel mix; optimizing excess air to minimize heat losses via unburned gases or unburned residues);  High-thermal-efficiency heater designs with good control systems (e.g., oxygen trim);  Prevention of the condensation of exhaust gas on surfaces;  Minimization of power requirements by use of high-efficiency pumps, fans, and other equipment;  Techniques to control CO emissions, such as good operation and control, constant delivery of liquid fuel in the secondary heating, good mixing of the exhaust gases, and catalytic afterburning;  Regular cleaning of heating surface (soot blowing) for liquid fuel or mixed firing; and  High-emissivity refractories for radiant heat transfer improvement, e.g., by application of ceramic coatings as reflecting surfaces. Venting and Flaring 11. Venting and flaring are important operational and safety measures used in petroleum refining facilities, particularly during non-routine operational periods such as malfunction or upset, as a means of safely disposing of vapors. Hydrocarbons are emitted from emergency process vents and safety valve discharges. These are collected in the blow-down network that is flared. 12. For planned start-up and shutdown, a flare gas recovery system should be used. During non- emergency releases, excess gas from process vents should be recovered or controlled and the volume of gas to be flared should be minimized. 13. Flaring modifies, by means of combustion, the chemical nature of the emitted substances (e.g., the combustion of H2S generates sulfur dioxide (SO2), while the combustion of hydrocarbon generates CO2 plus water vapor). Monitoring of gas emissions should encompass both the concentration of pollutants at ground level as well the total quantity of pollutants released annually. Before flaring is adopted, feasible alternatives for the use of the gas should be evaluated and —where practical, reasonable, and safe— integrated into production design to the maximum extent possible. Flaring volumes for new facilities should be estimated during the initial commissioning period so that fixed-volume flaring targets can be developed. The volumes of gas flared for all flaring activities should be recorded. Flare management plans should be prepared and implemented.2 2 Such as; U.S. EPA, 40 CFR 60 Standard of Performance for New Stationary Sources- Subpart Ja (2015). 3 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 14. The following pollution prevention and control measures should be considered for gas flaring:  Implementing source gas reduction measures to the maximum extent possible;  Using efficient flare tips (i.e., optimal released gas sonic velocity, in order to avoid malfunctioning of the flare due to its flame off), and optimization of the size and number of burner nozzles (not less than three, which will ensure—acting as pilot burners, positioned 120° from each other —the continuity of flaring);  Maximizing flare combustion efficiency by controlling and optimizing flare fuel/air/steam flow rates to ensure the correct ratio of assist stream to flare stream;  Minimizing flaring from purges and pilots, without compromising safety, through measures including the installation of purge gas reduction devices, flare gas recovery units (mainly for continuous or predictable releases), an upstream knock-out drum (vapor–liquid separator used to avoid entrainment of liquid to the flare stack), soft-seat valve technology (where appropriate), conservation pilots, the use of inert purge gas, and the diversion of flows into the refinery fuel gas distribution network;  Minimizing the risk of pilot blow-out by ensuring sufficient exit tip velocity and providing wind guards;  Using a reliable pilot auto-ignition system;  Installing high-integrity instrument pressure protection systems, where appropriate, to reduce over-pressure events and avoid or reduce flaring situations;  Minimizing liquid carry-over and entrainment in the gas flare stream with a suitable liquid separation system;  Minimizing flame lift (flash off) and flame lick (flash back);  Operating flares to control odor and visible smoke emissions using suitable optical instruments, such as flame detectors, which act on the steam injection in case of black smoke at tip;  Locating flares at a safe distance from local communities and the workforce, including workers’ accommodation units;  Implementing burner maintenance planning and replacement programs to ensure continuous maximum flare efficiency;  Metering flare gas on a monthly basis in the interest of pollution evaluation, mainly in terms of CO2 and SO2, as well as of released heat (which is an indirect estimation of the greenhouse gas (GHG) emissions);  Avoiding over-steaming, as too much steam in a flare will reduce flare performance;  Avoiding a wake-dominated flame. A strong crosswind at high velocity can have a powerful effect on the flare’s flame dimensions and shape, causing the flame to be wake -dominated (i.e., the flame is bent over on the downwind side of a flare and imbedded in the wake of the flare tip), reducing flare performance and potentially damaging the flare tip; and  Avoiding flame lift-off, a condition in which a flame separates from the tip of the flare and there is space between the flare tip and the bottom of the flame due to excessive air induction as a result of the flare gas and center steam exit velocities. This type of flame can reduce flare performance and can progress to a condition where the flame becomes completely extinguished. 4 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 15. To minimize flaring events as a result of equipment breakdowns and plant upsets, plant reliability should be high (>95 percent). Provisions should be made for taking equipment offline for planned maintenance regimes and plant turnaround protocols, to the extent that the refinery does not exceed 8,000 operating hours/year (corresponding to one month/year of refinery-planned shut-down for general maintenance). This means achieving a Refinery Service Factor of 91 percent (or 8,000 operating hours/24 hours per day x 365 days= 0.91). Fugitive Emissions 16. Fugitive emissions in petroleum-refining facilities may occur from leaking tubing, valves, connections, flanges, gaskets, steam traps, packing, open-ended lines, floating roof storage tanks and pump seals, gas conveyance systems, compressor seals, pressure relief valves, breathing valves, tanks or open pits/containments, oil-water separators, and in the storage, loading, and unloading operations of hydrocarbons. Depending on the refinery process scheme, fugitive emissions may comprise:  Hydrogen;  Methane;  Volatile organic compounds (VOCs), (e.g., ethane, ethylene, propane, propylene, butanes, butylenes, pentanes, pentenes, C6-C9 alkylate, benzene, toluene, xylenes, phenol, and C9 aromatics);  Polycyclic aromatic hydrocarbons (PAHs) and other semi-VOCs;  Inorganic gases, including ammonia (NH3), CO, CO2, SO2 and sulfur trioxide (SO3) from sulfuric acid regeneration in the sulfuric acid alkylation process, NOx, methyl tertiary butyl ether (MTBE), ethyl tertiary butyl ether (ETBE), t-amylmethyl ether (TAME), methanol, and ethanol; and  If occurring, hydrofluoric acid (HF) from hydrogen fluoride alkylation and H2S. 17. There is significant potential for VOC emissions from cone-roof storage tanks during loading due to fugitive releases from the out-breathing valves; fugitive emissions of hydrocarbons through the roof seals of floating roof storage tanks; fugitive emissions from flanges and/or valves and machinery seals; VOC emissions from blending tanks, valves, pumps, and mixing operations; and VOC emissions from oily sewage and wastewater treatment systems. It is also possible for nitrogen to be emitted from bitumen storage tanks and possibly saturated with hydrocarbons and sulfur compounds at storage temperature (150–180°C) in the form of aerosols. Other potential fugitive emission sources include the vapor recovery unit vents and gas emissions from caustic oxidation. 18. Recommendations to prevent and limit fugitive emissions include the following:  A structured leak detection and repair (LDAR) program should be implemented; based on a systematic review of Process and Instrumentation Diagrams (P&IDs), this program should identify streams and equipment (e.g., pipes, valves, seals, tanks, and other infrastructure components) where fugitive VOC emissions are a possibility (through component degradation, for example) and prioritize their monitoring with vapor detection equipment, followed by maintenance or replacement of components, as needed. 5 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016  When selecting appropriate valves, packings, flanges, fittings, and seals, consideration should be given to their effectiveness to reduce gas leaks and fugitive emissions.3  To minimize their release to the atmosphere, hydrocarbon vapors should be either contained (e.g., using a nitrogen blanketing system an internal floating roof for tanks, or a cover system for separator) or routed back to the process.  Installing a Vapors Recovery Unit, in lieu of open venting or flaring. Use of vent gas scrubbers should be considered to remove oil and other oxidation products from overhead vapors in specific units (e.g., bitumen production, loading racks).  The incineration of gas should be conducted at a high temperature (approximately 800°C) to ensure complete destruction of minor components (e.g., H2S, aldehydes, organic acids, and phenolic components) and to minimize emissions and odor impacts.  With regard to emissions from HF, alkylation plant vents should be collected and neutralized for HF in a scrubber before being sent to flare.  With regard to naphtha, gasoline, methanol/ethanol, and ethers—including MTBE, ETBE, and TAME—loading/unloading racks should be provided with vapor controls, e.g. vapor recovery units.  Additional guidelines for the prevention and control of fugitive emissions from storage tanks are provided in the EHS Guidelines for Crude Oil and Petroleum Product Terminals . Nitrogen Oxides 19. NOx may be emitted from boilers, process heaters, furnaces, Combined Heat Power (CHP) units, gas turbines, fluid catalytic cracking (FCC) regenerators, as well as flare and other process and combustion units. NOx formation arises from three mechanisms: fuel NOx (due to nitrogen content in the fuel), thermal NOx (due to nitrogen in the air under high temperatures and excess air conditions during combustion), and prompt NOx (due to the reaction of atmospheric nitrogen (N 2) with free radicals such as C, CH, and CH 2 fragments derived from fuel in the earliest stage of combustion). To reduce NO x emissions, low-NOx burners are the most commonly installed technology on combustion devices, while controlling NOx emissions associated with FCCs typically involve the consideration of selective catalytic reduction (SCR) or thermal de-NOx technologies. 20. The ammonia (NH3) formed during the naphtha and gasoil hydrodesulfurization process is fed as a component of the sour feed gas to the thermal reactor of the SRU and converted to fuel NO x. In addition, thermal NOx is formed at the SRU due to high-temperature (approximately 1,400°C) oxidation of nitrogen from the process air. 21. In addition to the guidance for the management of these issues presented in the General EHS Guidelines, recommended pollution prevention and minimization measures include High-Temperature Air Combustion (HiTAC), otherwise called flameless (or colorless) combustion. It can be used in SRUs, especially those employing lean acid gas streams, which cannot be burned without the use of auxiliary fuel or oxygen enrichment under standard conditions. With the use of HiTAC, lean acid gas streams can be burned with uniform thermal fields without the need for fuel enrichment or oxygen addition. The uniform 3 European Commission (EC) Joint Research Center (JRC), Best Available Techniques Reference (BREF) Document for the Refining of Mineral Oil and Gas (2015). 6 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 temperature distribution favors clean and efficient burning, with an additional advantage of significant reduction of NOx, CO, and hydrocarbon emission. Sulfur Oxides 22. Sulfur oxides (SOx) and H2S may be emitted from boilers, heaters, and other process units (such as SRUs, FCC regenerators, flares, wastewater stripping, incondensable off-gas incinerators, decoking operations, and coke calcinations). Emissions will vary according to the sulfur content of the processed crude oil, the sulfur content of the fuel that is being combusted, the degree of sulfur recovery, and the level of SOx emission controls. Sulfur dioxide (SO2) and sulfur trioxide (SO3) may be emitted from sulfuric acid regeneration in the sulfuric acid alkylation process. In refinery off gases, SO2 may have pre-abatement concentration levels of 1,500–7,500 milligrams per cubic meter (mg/m 3). 4 23. To reduce SOx emissions and improve product quality, sulfur-bearing refinery streams are typically directed to hydrotreating units where hydrogen combines with sulfur to form H2S; this, in turn, is directed to the Amine Unit, from which a single stream, at high H2S concentration, is sent to the SRU, generally based on the Claus process.5 24. Recommended pollution prevention and minimization measures include the following:  Minimize SOx emissions through desulfurization of fuels, to the extent feasible, or by directing the use of high-sulfur fuels to units equipped with SOx emission controls.  Recover sulfur from tail gases using high-efficiency SRUs (e.g., Claus units, equipped with the specific section of Tail Gas Treatment (TGT)). 6  Install scrubbers with caustic soda solution to treat flue gases (caustic wash of acid gas stream, to remove acids) from the alkylation unit absorption towers. Particulate Matter 25. Particulate emissions from refinery units are associated with flue gas from furnaces and boilers; catalyst fines emitted from fluidized catalytic cracking regeneration units and other catalyst-based chemical processes; the handling of pet-coke; fines and ash generated during incineration of sludge; and decoking and soot blowing off furnaces and flares. Particulates may contain metals (e.g., vanadium, nickel). Condensable PM2.5 (e.g., nitrates, sulfates) are another type of particulate emissions. Measures to control particulates may also contribute to control of metal emissions from petroleum refining.7 26. Recommended pollution prevention and minimization measures include the following:  On large sources of particulate matter emissions such as FCCU regeneration units and sludge incinerators, install high-efficiency air pollution control devices (e.g., bag filters, electrostatic 4 EC European Integrated Pollution Prevention and Control Bureau (EIPPCB), Best Available Techniques (BAT) Reference Document for Refineries (2003). 5 See Annex A: General Description of Petroleum Industry Activities. 6 A sulfur recovery system with at least 97 percent but preferably over 99 percent sulfur recovery should be used when the hydrogen sulfide concentration in tail gases is significant. 7 EC JRC, Best Available Techniques Reference (BREF) Document for the Refining of Mineral Oil and Gas (2015). 7 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 precipitators, scrubbers, third-stage cyclones). Consider these technologies along with NO x and SOx emissions control technologies (e.g., wet gas scrubbers) if PM2.5 control is warranted. A combination of these techniques may achieve >99 percent abatement of particulate matter.  Implement particulate emission reduction techniques during coke handling, including: o Store (green sponge) pet-coke in bulk under enclosed shelters; o Keep coke constantly damp; o Cut coke in a crusher and convey it to an intermediate storage silo (hydrobins); o Spray coke with a fine layer of gasoil, to stick the dust fines to the coke; o Use covered conveyor belts with extraction systems to maintain a negative pressure; o Use aspiration systems to extract and collect coke dust; and o Pneumatically convey the fines collected from the cyclones into a silo fitted with exit air filters, and recycle the collected fines to storage.  Consider fuel switching, e.g., replace heavy fuel oil with light fuel oil, natural gas, or refinery gas. Greenhouse Gases 27. Carbon dioxide (CO2) and methane (CH4) are the primary greenhouse gases (GHGs) emitted by the petroleum refining industry and may be produced in significant amounts during petroleum refining and related combustion processes. Carbon dioxide and other gases (e.g., N 2O) may be discharged to the atmosphere during the in-situ catalyst regeneration of noble metals. Aggregate GHG emissions should be quantified annually in accordance with internationally recognized methodologies. 28. Operators should include at the design stage or when considering major revamping improvements enhancement to stationary combustion sources (i.e., steam generation boilers, process heaters, combined heat and power), upgrading fuel gas systems and flares, and installing power/waste heat recovery units to minimize GHG emissions. The overall objective should be to reduce GHG emissions and evaluate cost- effective options for reducing emissions that are technically feasible. 8 Additional recommendations for the management of GHGs, in addition to energy efficiency and conservation, are addressed in the General EHS Guidelines. Wastewater Industrial Process Wastewater 29. Significant volumes of wastewaters in petroleum refining include “sour” process wastewater and non- oily/non-sour process wastewater. Sour wastewater is generated from desalting, topping, vacuum distillation, pretreating, light- and middle-distillate hydrodesulfurization, hydrocracking, catalytic cracking, coking, and visbreaking/thermal cracking. Sour wastewater may be contaminated with hydrocarbons, H2S, NH3, organic sulfur compounds (R-S-H mercaptans), organic acids, and phenol. Process wastewater that is high in H2S and/or NH3 is treated in the Sour Water Stripper Unit (SWSU) to remove these and other 8Detailed information on energy efficiency opportunities for petroleum refineries is presented in University of California, “Energy Efficiency Improvement and Cost Saving Opportunities for Petroleum Refineries” (2005) http://repositories.cdlib.org/cgi/viewcontent.cgi?article=3856&context=lbnl; and in U.S. EPA, “Available and Emerging Technologies for Reducing Greenhouse Gas Emissions from the Petroleum Refining Industry” (2010). 8 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 compounds, before recycling for internal process uses, or before final treatment and disposal through an on-site wastewater treatment unit. Non-oily/non-sour process wastewater has the potential to cause wastewater treatment plant (WWTP) disturbances. Boiler blowdown and demineralization plant reject streams have the undesirable potential to extract phenolic compounds from the oil phase into the water phase, as well as cause emulsions in the WWTP if incorrectly neutralized. Liquid wastewater may also result from accidental releases or leaks of small quantities of products from process equipment, machinery, and storage areas/tanks. Treated sour water is typically returned to the SWSU for stripping, rather than being sent to a refinery’s wastewater treatment plant . 30. Recommended process wastewater management practices include:  Prevention and control of accidental releases of liquids through regular inspections and maintenance of storage and conveyance systems, including stuffing boxes on pumps and valves and other potential leakage points, as well as the implementation of spill response plans;  Provision of sufficient capacity for storing process fluids to enable maximum recovery into the process and, as a consequence, avoiding large discharges of process liquids into the oily wastewater drainage system;  Design and construction of wastewater and hazardous materials storage containment basins with suitably impervious surfaces to prevent infiltration of contaminated water into soil and groundwater;  Segregation of process wastewater from storm water and segregation of wastewater and hazardous materials containment basins; and  Implementation of good housekeeping practices, including conducting product transfer activities over paved areas and prompt collection of small spills. 31. Specific provisions to be considered for the management of individual wastewater streams include the following:  Direct spent caustic soda from sweetening units and chemical treating to the wastewater treatment system following caustic oxidation.  Direct spent caustic liquor from caustic oxidation (containing soluble thiosulfates, sulfites, and sulfates) to the wastewater treatment system.  Install a closed-process drain system to collect and recover leakages and spills of MTBE, ETBE, and TAME. These substances are not responsive to biological treatment and should be prevented from entering and adversely affecting the wastewater treatment system.  If present at the facility, acidic and caustic wastewater from the demineralized water preparation should be neutralized prior to discharge into the wastewater treatment system.  Cool blowdown from the steam generation systems prior to discharge. This wastewater, as well as blowdown from cooling water towers, may contain additives (e.g., biocides) that may require treatment in the WWTP prior to discharge.  Hydrocarbon-contaminated water from scheduled cleaning activities during facility turnaround and hydrocarbon-containing wastewaters from process leaks should be treated in the WWTP. 9 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 Process Wastewater Treatment 32. Techniques for treating industrial process wastewater in this sector include source segregation and pretreatment of concentrated wastewater streams. Typical wastewater treatment steps include:  Grease traps, oil skimmers, Coalescing Plate Separators (CPS), Dissolved Air Flotation (DAF) or oil water separators for separation of oils and floatable solids;  Filtration for separation of filterable solids;  Flow and load equalization;  Sedimentation for suspended solids reduction using clarifiers;  Biological treatment—typically aerobic treatment—for the reduction of soluble organic matter, measured as Biological Oxygen Demand (BOD);  Chemical or biological nutrient removal for reduction of nitrogen and phosphorus;  Chlorination of wastewater when disinfection is required; and  Dewatering and disposal of residuals in designated hazardous waste landfills. 33. Additional engineering controls may be required for: (i) containment and treatment of volatile organics stripped from various unit operations in the wastewater treatment system; (ii) advanced metals removal using membrane filtration or other physical/chemical treatment technologies; (iii) removal of recalcitrant organics and non-biodegradable Chemical Oxygen Demand (COD) using activated carbon or advanced chemical oxidation; (iii) reduction in wastewater toxicity using appropriate technology (such as reverse osmosis, ion exchange, activated carbon); and (iv) containment and neutralization of nuisance odors. 34. Management of industrial wastewater and examples of treatment approaches are discussed in the General EHS Guidelines. Through the use of these technologies and good practice techniques for wastewater management, facilities should meet the guideline values for wastewater discharge as indicated in the relevant table of Section 2 of this industry sector document. Other Wastewater Streams & Water Consumption 35. Guidance on the management of non-contaminated wastewater from utility operations, non- contaminated storm water, and sanitary sewage is provided in the General EHS Guidelines. Contaminated streams should be routed to the treatment system for industrial process wastewater. Recommendations to reduce water consumption, especially where it may be a limited natural resource, are provided in the General EHS Guidelines. 36. Hydrostatic Testing Water: Hydrostatic testing (hydro-test) of equipment and pipelines involves pressure testing with water (generally, filtered raw-water) to verify system integrity and to detect possible leaks. Chemical additives (e.g., a corrosion inhibitor, an oxygen scavenger, and a dye) are generally added to the fresh water to prevent internal corrosion and to highlight leaks. In managing hydro-test waters, the following pollution prevention and control measures should be implemented: 10 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016  Use the same water for multiple tests;  Reduce the need for corrosion inhibitors and other chemicals by minimizing the time that test water remains in the equipment or pipeline; and  If chemical use is necessary, select effective chemicals with the lowest toxicity, bioavailability, and bioaccumulation potential, and with the highest biodegradability. 37. If discharge of hydro-test waters to the sea or to surface water is the only feasible alternative for disposal, a hydro-test water disposal plan should be prepared that considers points of discharge, rate of discharge, chemical use and dispersion, environmental risk, and required monitoring. Hydro-test water disposal into shallow coastal waters should be avoided. Handling of Hazardous Materials 38. Petroleum refining facilities manufacture, use, and store significant amounts of hazardous materials, including raw materials, intermediate/final products, and by-products. Recommended practices for hazardous material management—including handling, storage, and transport—are presented in the EHS Guidelines for Crude Oil and Petroleum Product Terminals and in the General EHS Guidelines. Wastes 39. There are numerous larger-volume wastes, both hazardous and non-hazardous, generated as a result of refining processes and maintenance operations. General guidance on the storage, handling, treatment, and disposal of hazardous and non-hazardous wastes is provided in the General EHS Guidelines. Spent Catalysts 40. Spent catalysts result from several process units in petroleum refining, including the pretreating and catalytic reformer; light- and middle-distillate hydrodesulfurization; the hydrocracker; FCCU; RCCU; MTBE/ETBE and TAME production; butanes isomerization; the dienes hydrogenation and butylenes hydro- isomerization unit; sulfuric acid regeneration; selective catalytic hydrodesulfurization; and the sulfur and hydrogen plants. Spent catalysts may contain molybdenum, nickel, cobalt, platinum, palladium, vanadium iron, copper, and silica and/or alumina, as carriers. There are several types of spent catalysts, and their physiochemical properties influence their handling. The two primary considerations are whether the specific catalyst is considered to be “hazardous” or “non-hazardous” in nature, and whether the metal(s) they contain are valuable or recoverable. An analysis of these factors will directly influence the handling of a spent catalyst. 41. Recommended management strategies for hazardous catalysts include the following:  Use long-life catalysts and regeneration to extend the catalyst lifecycle;  Use appropriate on-site storage and handling methods to avoid uncontrolled exothermic reactions; and  Return spent catalysts to the manufacturer for regeneration or recovery, or transport to other off- site management companies for handling, heavy or precious metals recovery/recycling, and disposal in accordance with industrial waste management recommendations included in the General EHS Guidelines. 11 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 Other Hazardous Wastes 42. In addition to hazardous spent catalysts, industrial hazardous waste may include solvents; filters; mineral spirits; used sweetening; spent amines for CO2, H2S, and carbonyl sulfide (COS) removal; activated carbon filters and oily sludge from oil/water separators and desalters; tank emulsions or bottoms; and spent or used operational and maintenance fluids (e.g., oils and test liquids). Other hazardous wastes, including contaminated sludges, sludge from jet water pump circuit purification, exhausted molecular sieves, and exhausted alumina from HF alkylation, may be generated from crude oil storage tanks, desalting and topping, coking, propane, propylene, butanes streams dryers, and butanes isomerization. WWTPs and basins/lagoons generate sludge that may need to be considered as hazardous waste, depending on the treatment process itself and on the incoming wastewater. 43. Process wastes should be tested and classified as hazardous or non-hazardous based on local regulatory requirements or internationally accepted approaches. Detailed guidance on the storage, handling, treatment, and disposal of hazardous and non-hazardous wastes is provided in the General EHS Guidelines. 44. Recommended industry-specific management strategies for hazardous waste include the following:  Send oily sludges—such as those from crude oil storage tanks (bottom drains) and from desalter (bottom drains)—to the delayed coking drum, where applicable, to recover the hydrocarbons.  Ensure excessive cracking is not conducted in the visbreaking unit to prevent production of an unstable fuel oil, resulting in increased sludge and sediment formation during storage.  Maximize recovery of oil from oily wastewaters and sludges. Minimize losses of oil to the wastewater system. Oil can be recovered from slops using separation techniques (e.g., gravity separators and centrifuges).  Sludge treatment may include land application (bioremediation) or solvent extraction, followed by combustion of the residue and/or use in asphalt or cement kilns, where feasible. In some cases, the residue may require stabilization prior to disposal to reduce the leachability of toxic metals. When not treated, the hazardous sludge from crude oil refineries must be disposed of in a secured landfill, as indicated in the General EHS Guidelines. Non-Hazardous Wastes 45. HF alkylation produces neutralization sludge, which may contain calcium fluoride, calcium hydroxide, calcium carbonate, magnesium fluoride, magnesium hydroxide and magnesium carbonate. After drying and compression, they may be marketed for uses—in steel mills, for example—or landfilled. Detailed guidance on the storage, handling, treatment, and disposal of non-hazardous wastes is provided in the General EHS Guidelines. Noise 46. The principal sources of noise in petroleum refining facilities include large rotating machines, such as compressors and turbines, pumps, electric motors, air coolers (if any), blowers, fans, and heaters. In addition, steam leaks, if significant, can be noisy. During emergency depressurization, high noise levels 12 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 can be generated due to high-pressure gases released to flare and/or steam release into the atmosphere. General recommendations for noise management are provided in the General EHS Guidelines. 1.2 Occupational Health and Safety 47. The occupational health and safety issues that may occur during the construction and decommissioning of petroleum refining facilities may be similar to those of other industrial facilities, and their management is discussed in the General EHS Guidelines. 48. As a general approach, process health and safety management planning should include the adoption of a systematic and structured approach for the prevention and control of physical, chemical, biological, and radiological health and safety hazards described in the General EHS Guidelines. 49. Major occupational health and safety hazards should be prevented through the implementation of a Process Safety Management Program that includes all of the minimum elements outlined in the General EHS Guidelines, including:  Facility-wide risk analysis, including a detailed consequence analysis (e.g., failure mode and effects analysis (FMEA), hazard identification study (HAZID), hazard and operability study (HAZOP), or quantitative risk assessment (QRA)). This analysis is expected to be carried out alongside the Front End Engineering Design (FEED) and with the Detailed Engineering Design prior to commissioning;  Employee training on operational hazards;  Procedures for the management of change in operations, process hazard analysis, maintenance of mechanical integrity, pre-start review, hot work permits, safe systems of work (SSW), and other essential aspects of process safety included in the General EHS Guidelines;  Safe Transportation Management System, as noted in the General EHS Guidelines, if the project includes a transportation component for raw or processed materials;  Procedures for handling, transportation, and storage of hazardous materials. 50. The most significant occupational health and safety hazards prevalent during the operational phase of a petroleum refining facility primarily include:  Process safety;  Oxygen-deficient atmosphere;  Chemical hazards;  Fire and explosions. Process Safety 51. Process safety programs should be implemented based on industry-specific conditions, such as complex chemical reactions, use of hazardous materials (e.g., toxic, reactive, volatile, flammable, or explosive compounds), and multi-step reactions. 13 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 52. Process safety management should include the following:  Physical hazard testing of materials and reactions;  Hazard analysis studies to review the process chemistry and engineering practices, including thermodynamics and kinetics;  Effective preventive maintenance routines and examination of the mechanical integrity of the process equipment and utilities;  Operator/technician training and development; and  Development of SSW, operating instructions, and emergency response procedures. Oxygen-deficient Atmosphere 53. The potential release and accumulation of nitrogen gas into work areas may result in the creation of asphyxiating conditions due to the displacement of oxygen. Prevention and control measures to reduce the risks of asphyxiant gas release include:  Design and placement of nitrogen venting systems according to industry standards;  Installation of an automatic Emergency Shutdown System that can detect and sound an alarm warning of the uncontrolled release of nitrogen (including the presence of oxygen-deficient atmospheres in working areas9), automatically initiate forced ventilation, and shut down equipment to minimize the duration of releases;  Implementation of confined space entry procedures as described in the General EHS Guidelines, with consideration of facility-specific hazards. Chemical Hazards 54. Releases of hydrofluoric acid, carbon monoxide, methanol, and H 2S may present occupational exposure hazards. H2S leakage may occur from amine regeneration in amine treatment units, and SRUs. CO leakage may occur from FCCU and RCCU and from the syngas production section of the Hydrogen Plant. CO/air mixtures are explosive and spontaneous; explosive re-ignition may occur. H2S poses an immediate fire hazard when mixed with air. 55. Workers may be exposed to potential inhalation hazards (e.g., H2S, CO, VOCs, PAHs) during routine plant operations. Dermal hazards may include contact with acids, steam, and hot surfaces. Chemical hazards should be managed based on the results of a job safety analysis and industrial hygiene survey and according to the occupational health and safety guidance provided in the General EHS Guidelines. Protection measures include worker training, work permit systems, use of personal protective equipment (PPE), and toxic gas detection systems with alarms.10 9 Working areas with the potential for oxygen-deficient atmospheres should be equipped with area monitoring systems capable of detecting such conditions. Workers also should be equipped with personal monitoring systems. Both types of monitoring systems should be equipped with a warning alarm set at 19.5 percent concentration of O 2 in the air. 10 A detailed description of health and safety issues and prevention/control strategies associated with petroleum refining, including chemical and fire/explosion hazards, is available in Occupational Safety and Health Association 14 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 Hydrofluoric Acid 56. Workers may be exposed to hydrofluoric acid (HF) in the HF alkylation unit. Occupational safety measures include the following:11  Reducing HF volatility by adding suitable vapor pressure suppression additives;  Minimizing HF hold-up volume (circuit inventory);  Designing the plant layout to limit the extent of the plant area exposed to potential HF hazards, and to facilitate escape routes for workers;  Clearly identifying HF hazardous areas, and indicating where PPE must be adopted;  Implementing a worker decontamination procedure in a dedicated area;  Implementing a safety distance buffer between the HF alkylation unit, other process units, and the refinery boundary;  Use of scrubbing systems to neutralize and remove HF prior to flaring;  Use of an HF neutralization basin for wastewater before it is discharged into the refinery’s oily wastewater system;  Use of a dedicated tank to collect alkylate product and undertake routine pH measurements before dispatching to gasoline pool;  Treating butane and propane products in alumina defluorinators to destroy organic fluorides, followed by alkali to remove any remaining HF; and  Transport of HF to and from the plant should be handled according to guidance for the transport of dangerous goods, as described in the General EHS Guidelines. Fire and Explosions 57. Fire and explosion hazards generated by process operations include the accidental release of syngas (containing carbon monoxide and hydrogen), oxygen, methanol, and refinery gases. Refinery gas releases may cause “jet fires” if ignited in the release section, or give rise to a vapor cloud explosion (VCE), fireball, or flash fire, depending on the quantity of flammable material involved and the degree of confinement of the cloud. Methane, hydrogen, carbon monoxide, and H2S may ignite even in the absence of ignition sources at temperatures that are higher than their auto-ignition temperatures of 580°C, 500°C, 609°C, and 260°C, respectively. Flammable liquid spills present in petroleum refining facilities may cause “ pool fires.” Explosive hazards may also be associated with the accumulation of vapors in storage tanks (e.g., sulfuric acid and bitumen). 58. Recommended measures to prevent and control fire and explosion risks from process operations include the following:12 (OSHA), Technical Manual, Section IV Safety Hazards, Chapter 2 (1999) “Petroleum Refining Process,” available at http://www.osha.gov/dts/osta/otm/otm_iv/otm_iv_2.html. 11 Recommendations for the handling of hydrofluoric acid are available in American Petroleum Institute (API), Recommended Practice (RP) 751, “Safe Operation of Hydrofluoric Acid Alkylation Units” (Third Edition, June 2007). 12 Further recommendations for fire and explosion hazards are available in API, RP 2001, “Fire Protection in Refineries” (2012). 15 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016  Designing, constructing, and operating petroleum refineries according to international standards13 for the prevention and control of fire and explosion hazards, including provisions for segregation of process, storage, utility, and safe areas. Safety distances can be derived from specific safety analyses for the facility and the QRA, and through application of internationally recognized fire safety standards;14  Providing early warning systems, such as pressure monitoring of gas and liquid conveyance systems, in addition to smoke and heat detection for fires;  Evaluation of potential for vapor accumulation in storage tanks and implementation of prevention and control techniques (e.g., nitrogen blanketing for sulfuric acid and bitumen storage);  Avoiding potential sources of ignition (e.g., by configuring the layout of piping to avoid spills over high-temperature piping, equipment, and/or rotating machines);  Providing passive fire protection measures within the modeled fire zone that are capable of withstanding the fire temperature for a time sufficient to allow the operator to implement the appropriate fire mitigation strategy;  Limiting/containing the areas that may be potentially affected by the accidental releases of flammable liquids by; o Defining fire zones and equipping them with a drainage system to collect and convey accidental releases of flammable liquids to a safe containment area, including secondary containment of storage tanks; o Installing fire/blast partition walls in areas where appropriate separation distances cannot be achieved; and o Designing the oily wastewater system to avoid the propagation of fire. 59. Further recommendations on the management of fire and explosion hazards relating to crude oil storage are addressed in the EHS Guidelines for Crude Oil and Petroleum Product Terminals. 1.3 Community Health and Safety 60. Community health and safety impacts during the construction and decommissioning of petroleum refining facilities are common to those of most other industrial facilities and are discussed in the General EHS Guidelines. 61. The most significant community health and safety hazards associated with petroleum refining facilities occur during the operational phase, including the threat from major accidents related to fires and explosions at the facility and potential accidental releases of raw materials or finished products during transportation outside the processing facility. Guidance for the management of these issues is presented below and in the General EHS Guidelines. 13 An example of good practice includes the U.S. National Fire Protection Association (NFPA), Code 30: “Flammable and Combustible Liquids” (Quincy, MA: NFPA, 2003), available at http://www.nfpa.org/. Further guidance to minimize exposure to static electricity and lightening is available in API, RP, “Protection against Ignitions Arising out of Static, Lightning, and Stray Currents” (2003). 14 An example of further information on safe spacing is NFPA Code 30 (2003). 16 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 62. Additional relevant guidance applicable to transport by sea and rail as well as to shore-based facilities can be found in the EHS Guidelines for Shipping, Railways, Ports, and Harbors, and the EHS Guidelines for Crude Oil and Petroleum Products Terminals. Major Hazards15 63. The most significant safety hazards are related to the handling and storage of liquid and gaseous substances. Impacts may include significant exposures to workers and, potentially, to surrounding communities, depending on the quantities and types of accidentally released chemicals and the conditions for reactive or catastrophic events, such as fire and explosion. 16 Main measures for reduction of these risks are presented in Section 1.2. Emergency planning, to prevent major hazards to the community should include, at a minimum, the preparation and implementation of an Emergency Management Plan, prepared with the participation of local authorities and potentially affected communities. Additional guidance is provided in the General EHS Guidelines. 15 A detailed description of health and safety issues and prevention/control strategies associated with petroleum refining, is available in OSHA, Technical Manual, Section IV Safety Hazards, Chapter 2 (1999) “Petroleum Refining Process,” available at http://www.osha.gov/dts/osta/otm/otm_iv/otm_iv_2.html. 16 Further recommendations for fire and explosion hazards are available in API, RP 2001, “Fire Protection in Refineries” (2012). 17 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 2. PERFORMANCE INDICATORS MONITORING 2.1 Environment Emissions and Effluent Guidelines 64. Tables 1 and 2 present emission and effluent guidelines for the Petroleum Refining sector. Guideline values for process emissions (such as FCCU, SRU, and combustion units) and effluents in this sector are indicative of good international industry practice, as reflected in relevant standards of countries with recognized regulatory frameworks. The guideline values are assumed to be achievable under normal operating conditions in appropriately designed and operated facilities through the application of pollution prevention and control techniques discussed in the preceding sections of this document. 65. Combustion source emissions guidelines associated with steam- and power-generation activities from sources with a capacity equal to or lower than 50 MWth are addressed in the General EHS Guidelines. Larger power source emissions from turbines, boilers, and engines are addressed in the EHS Guidelines for Thermal Power Plants. Emissions from multi-fuel fired combustion units such as process heaters and boilers are addressed in Table 1, together with other process emissions. Guidance on ambient considerations based on the total load of emissions is provided in the General EHS Guidelines. 66. Effluent guidelines are applicable to direct discharges of treated effluents to surface waters for general use. Site-specific discharge levels may be established based on the availability and conditions in use of publicly operated sewage collection and treatment systems or, if discharged directly to surface waters, on the receiving water use classification, as described in the General EHS Guidelines. a Table 1. Air Emissions Levels for Petroleum Refining Facilities Pollutant Units Guideline Value 300 NOX b mg/Nm3 100 for FCCU 150 for SRU; SOX c mg/Nm3 300 for FCCU 500 Particulate Matter (PM10) d mg/Nm3 25 Vanadium e mg/Nm3 5 Nickel mg/Nm3 1 H2S e mg/Nm3 5 a. Dry gas at 3 percent O2. b. NOx means NO+NO2 expressed in NO2 equivalent. Guideline value from European Commission Joint Research Center (EC JRC), “Best Available Techniques Reference (BREF) Document for the Refining of Mineral Oil and Gas” (2015). c. SOx means SO2 + SO3 expressed in SO2 equivalent. d. Guideline value from EC JRC, “BREF Document for the Refining of Mineral Oil and Gas” (2015). Particulate matter guideline value is also valid for FCCU. e. From G.S.R. 186(E) and 820(E), India Ministry of Environment and Forests Notification http://envfor.nic.in/legis/env_stand.htm. 18 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 a Table 2. Liquid Effluents Levels for Petroleum Refining Facilities Pollutant Units Guideline Value pH S.U. 6–9 BOD5 mg/L 30 b COD mg/L 125 c Total Suspended Solids (TSS) mg/L 30 Oil and Grease mg/L 10 Chromium (total) mg/L 0.5 Chromium (hexavalent) mg/L 0.05 Copper mg/L 0.5 Iron mg/L 3 Cyanide Total mg/L 1 Free 0.1 Lead mg/L 0.1 Nickel mg/L 0.5 Mercury mg/L 0.003 d Arsenic mg/L 0.1 Vanadium mg/L 1 Phenol mg/L 0.2 Benzene mg/L 0.05 e Benzo(a)pyrene mg/L 0.05 Sulfides mg/L 0.2 Total Nitrogen mg/L 10 f Total Phosphorus mg/L 2 Temperature increase C <3 g Notes: a. Assumes an integrated petroleum refining facility. b. Guideline value from EC JRC, BREF (2015) Table 3.16; National legislations may have lower values such as China: 20 mg/L. c. Guideline value from EC JRC, BREF (2015); National legislations may have lower values such as China: 120 mg/L. d. EC JRC, BREF (2015) Table 3.16. e. Guideline value from EC JRC, BREF (2015). f. The effluent concentration of nitrogen (total) may be up to 40 mg/l in processes that include hydrogenation. g. At the edge of a scientifically established mixing zone, which takes into account ambient water quality, receiving water use, potential receptors, and assimilative capacity. EC JRC, BREF (2015) Table 3.16. Environmental Monitoring 67. Environmental monitoring programs for the Petroleum Refining sector should be implemented to address all activities that have been identified to have potentially significant impacts on the environment, during both normal operations and upset conditions (emergencies and consequent flaring). Environmental 19 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 monitoring activities should be based on direct or indirect indicators of emissions, wastewater, and resource use applicable to the particular project, and for point sources of emissions this should include both concentration and mass flow rate of pollutants. 68. Monitoring frequency should be sufficient to provide representative data for the parameter being monitored. Monitoring should be conducted by trained individuals following suitable and appropriate monitoring and record-keeping procedures and using regularly calibrated and suitably maintained equipment. Monitoring data should be analyzed and reviewed at regular intervals and compared with the operating standards so that any necessary corrective actions can be taken. Additional guidance on applicable sampling and analytical methods for emissions and effluents is provided in the General EHS Guidelines. 69. In order to improve the management of fugitive emissions from the entire petroleum refinery and to protect human health in affected communities, in addition to monitoring and management requirements described in Section 1.1 of this Guideline, fence line monitoring of benzene concentration should be done according to internationally recognized methodologies. 17 Where annual average benzene concentrations associated with refinery emissions exceed the guideline value given in Table 3, corrective actions should be taken to reduce benzene emissions from refinery. Corrective actions and monitoring results should be reported. Table 3. Fence Line Monitoring Action Level Pollutant Guideline Value Benzene 9 µg/m3 a a. Annual average concentration that is corrected for background contribution. Guideline value from U.S. EPA 40CFR63 Subpart CC—National Emission Standards for Hazardous Air Pollutants from Petroleum Refineries (2015). Resource Use, Energy Consumption, Emission and Waste Generation 70. Tables 4 and 5 provide examples of resource consumption, and emission/waste quantities generated per million tons of processed crude oil. Industry benchmark values are provided for comparative purposes only, and individual projects should target continuous improvement in these areas. Table 4. Resource and Energy Consumption Parameter Definition of Parameter Unit Industry Benchmark Total energy consumed by MJ per metric ton the process, including Total Energy Consumption(1) of processed crude 2,300–3,300 direct combustion, steam, oil electricity, etc. kWh per metric ton Total electricity consumed Electric Power Consumption(1) of processed crude 22–31 by the process oil 17Such as U.S. EPA, 40 CFR 63 Subpart CC- National Emission Standards for Hazardous Air Pollutants from Petroleum Refineries (2015). 20 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 The supply of raw filtered water that integrates drift m3 per metric ton of Fresh Make-up Water(2) 0.07–0.66 and evaporation losses as processed crude oil well as blowdown Notes: 1. Based on CONCAWE, EU refinery energy systems and efficiency, Report No. 3/12. (2012); CONCAWE, Oil Refining Report No. 1/13 (2013); U.S. Energy Information Administration (EIA), Short Term Energy Outlook (2013). 2. Based on EC JRC, “BREF Document for the Refining of Mineral Oil and Gas” (2015). Table 5. Emission and Waste Generation Parameter Unit Industry Benchmark Wastewater m3/metric ton crude oil 0.1–1.51 Emissions CO22 105,000–276,000 NOx3 70–450 Particulate matter Metric ton /million metric tons of processed crude oil 60–150 SOx4 60–300 VOC 65–300 Solid waste 10–100 Notes: 1. Based on European Commission Joint Research Center (EC JRC), “Best Available Techniques Reference (BREF) Document for the Refining of Mineral Oil and Gas” (2015). 2. Not all GHGs, only total CO2. Based on EC JRC, “BREF Document for the Refining of Mineral Oil and Gas” (2015). 3. NO+NO2 expressed in NO2 equivalent. 4. SO2+SO3 expressed in SO2 equivalent. 2.2 Occupational Health and Safety Occupational Health and Safety Guidelines 71. Occupational health and safety performance should be evaluated against internationally published exposure guidelines, of which examples include the Threshold Limit Value (TLV®) occupational exposure guidelines and Biological Exposure Indices (BEIs®) published by the American Conference of Governmental Industrial Hygienists (ACGIH), 18 the Pocket Guide to Chemical Hazards published by the United States National Institute for Occupational Health and Safety (NIOSH), 19 Permissible Exposure Limits (PELs) published by the Occupational Safety and Health Administration of the United States (OSHA), 20 and Indicative Occupational Exposure Limit Values published by European Union member states, 21 or other similar sources. 18 Available at http://www.acgih.org/store/. 19 Available at http://www.cdc.gov/niosh/npg/. 20 Available at http://www.osha.gov/pls/oshaweb/owadisp.show_document?p_table=STANDARDS&p_id=9992. 21 Available at https://osha.europa.eu/en/legislation/directives/exposure-to-chemical-agents-and-chemical-safety/osh- related-aspects/council-directive-91-414-eec. 21 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 Accident and Fatality Rates 72. Projects should endeavor to reduce the number of incidents and near misses among project workers (whether directly employed or subcontracted) to a rate of zero, especially incidents that could result in lost work time, different levels of disability, or even fatalities. Facility rates may be benchmarked against the performance of facilities in this sector in developed countries through consultation with published sources (e.g., U.S. Bureau of Labor Statistics and U.K. Health and Safety Executive).22 Occupational Health and Safety Monitoring 73. The working environment should be monitored for occupational hazards relevant to the specific project. Monitoring should be designed and implemented by accredited professionals 23 as part of an occupational health and safety monitoring program. Facilities should also maintain a record of occupational accidents and diseases and dangerous occurrences and accidents. Additional guidance on occupational health and safety monitoring programs is provided in the General EHS Guidelines. 22Available at http://www.bls.gov/iif/ and http://www.hse.gov.uk/statistics/index.htm. 23Accredited professionals may include Certified Industrial Hygienists, Registered Occupational Hygienists, or Certified Safety Professionals or their equivalent. 22 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 3. REFERENCES American Petroleum Institute (API). 1992. Recommended Practice (RP) 751. “Safe Operation of Hydrofluoric Acid Alkylation Units.” Third Edition, June 2007. Washington, DC: API. Available at http://www.api.org/environment-health-and-safety/process-safety/process-safety-standards/standard- rp-751. ———2008. Recommended Practice (RP) 2003. “Protection Against Ignitions Arising out of Static, Lightning, and Stray Currents.” Seventh Edition. Washington, DC: API. Available at http://publications.api.org. ———2012. Recommended Practice (RP) 2001. “Fire Protection in Refineries.” Washington, DC: API. Available at http://publications.api.org. Conservation of Clean Air and Water in Europe (CONCAWE). 1999. “Best Available Techniques to Reduce Emissions from Refineries.” Brussels: CONCAWE. ———2009. “Refining BREF Review. Air Emissions.” Report No. 4/09. Brussels: CONCAWE. Available at https://www.concawe.eu. ———2012. “EU Refinery Energy Systems and Efficiency.” Report No. 3/12. Brussels: CONCAWE. Available at https://www.concawe.eu/uploads/Modules/Publications/rpt_12-03-2012-01520-01-e.pdf. ———2013. “Oil Refining.” Report No. 1/13. Brussels: CONCAWE. Available at https://www.concawe.eu/uploads/Modules/Publications/rpt_13-1r-2013-01142-01-e.pdf. European Commission (EC). 2003. European Integrated Pollution Prevention and Control Bureau (EIPPCB). “Best Available Techniques (BAT) Reference Document for Refineries (BREF).” Seville: EIPPCB. ———2015. European Integrated Pollution Prevention and Control Bureau (EIPPCB). “Best Available Techniques Reference (BREF) Document for the Refining of Mineral Oil and Gas.” Available at http://eippcb.jrc.ec.europa.eu/reference/BREF/REF_BREF_2015.pdf. European Union (EU). “Directive 2008/50/EC of the European Parliament and of the Council of 21 May 2008 on Ambient Air Quality and Cleaner Air for Europe.” Brussels/Strasbourg: European Union . German Federal Ministry for the Environment, Nature Conservation, and Nuclear Safety (BMU). 2002. “First General Administrative Regulation Pertaining to the Federal Emission Control Act (Technical Instructions on Air Quality Control – TA Luft).” Berlin: BMU. ———2004. “W aste Water Ordinance – AbwV. (Ordinance on Requirements for the Discharge of Waste Water into Waters).” Promulgation of the New Version of the Waste Water Ordinance of 17 June 2004. Berlin: BMU. Available at http://www.bmub.bund.de/fileadmin/bmu- import/files/pdfs/allgemein/application/pdf/wastewater_ordinance.pdf. IFP Energies Nouvelles. Water in Fuel Production, Oil Production, and Refining. Rueil-Malmaison Cedex – France. Available at www.ifpenergiesnouvelles.com. 23 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 Intergovernmental Panel on Climate Change (IPCC). 2005. Special Report. “Carbon Dioxide Capture and Storage.” Geneva: IPCC. Available at https://www.ipcc.ch/pdf/special- reports/srccs/srccs_wholereport.pdf. Italian Ministry of the Environment (Ministero dell’Ambiente). 1999. Servizio Inquinamento Atmosferico e Acustico e le Industrie a Rischio. Italian Refining Industry. Rome: Ministero dell’Ambiente. Maheu, A. 2009. Energy Choices and Their Impacts on Demand for Water Resources: An Assessment of Current and Projected Water Consumption in Global Energy Production. McGill University. Meyers, Robert. A. 1997. Handbook of Petroleum Refining Processes. New York, NY: McGraw-Hill Handbooks. UNESCO. 2008. IHE “Water Footprint of Bio-Energy and Other Primary Energy Carriers.” United States (U.S. Energy Information Administration (EIA). 2011. Annual Energy Review 2010. DOE/EIA-0384(2010). Washington, DC. Available at http://www.eia.gov/totalenergy/data/annual/archive/038410.pdf. ———2010. Petroleum Supply Annual 2009. DOE/EIA-0340(2009)/1. Washington, DC. Available at http://www.eia.gov/petroleum/supply/annual/volume1/archive/2009/psa_volume1_2009.html. ———2011. Petroleum Supply Annual 2010. DOE/EIA-0340(2010)/1. Washington, DC. Available at http://www.eia.gov/petroleum/supply/annual/volume1/archive/2010/psa_volume1_2010.cfm. ———AEO2012 National Energy Modeling System run REF2012.D020112C. Available at http://www.eia.gov/. ———“Short Term Energy Outlook.” May 2013. Available at http://www.eia.gov/forecasts/steo/archives/may13.pdf. United States (U.S.) Environmental Protection Agency (EPA). 40 CFR Part 60 “Standard of Performance for New Stationary Sources.” Subpart Kb—“Standards of Performance for Volatile Organic Liquid Storage Vessels (Including Petroleum Liquid Storage Vessels) for Which Construction, Reconstruction, or Modification Commenced after July 23, 1984.” Washington, DC: U.S. EPA. Available at http://www.ecfr.gov/cgi-bin/text- idx?SID=5bb86958f877cfc1cbddcba69e7716d2&mc=true&node=sp40.7.60.k_0b&rgn=div6. ———40 CFR Part 60 “Standard of Performance for New Stationary Sources.” Subpart J—“Standards of Performance for Petroleum Refineries.” Washington, DC: U.S. EPA. Available at http://www.ecfr.gov/cgi-bin/text- idx?SID=5bb86958f877cfc1cbddcba69e7716d2&mc=true&node=sp40.7.60.j&rgn=div6. ———40 CFR 60 Standard of Performance for New Stationary Sources. Subpart Ja—Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007. Washington, DC: Available at http://www.ecfr.gov/cgi-bin/text- idx?SID=5bb86958f877cfc1cbddcba69e7716d2&mc=true&node=sp40.7.60.j_0a&rgn=div6. ———40 CFR Part 60 “Standard of Performance for New Stationary Sources.” Subpart QQQ—“Standards of Performance for VOC Emissions From Petroleum Refinery Wastewater Systems.” Washington, DC: U.S. EPA. Available at https://www.law.cornell.edu/cfr/text/40/part-60/subpart-QQQ. 24 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 ———40 CFR Part 63. Subpart CC—“National Emission Standards for Hazardous Air Pollutants from Petroleum Refineries.” Washington, DC: U.S. EPA. Available at https://www.law.cornell.edu/cfr/text/40/part-63/subpart-CC. ———40 CFR Part 63. Subpart VV—“National Emission Standards for Oil-Water Separators and Organic-Water Separators.” Washington, DC: U.S. EPA. Available at https://www.law.cornell.edu/cfr/text/40/part-63/subpart-VV. ———40 CFR Part 419. “Petroleum Refining Point Source Category.” Washington, DC: U.S. EPA. Available at http://www.ecfr.gov/cgi-bin/text- idx?SID=6b51273d47e8dc451e0aac10f60cdfee&mc=true&node=pt40.31.419&rgn=div. 5. ———1995. “Compilation of Air Pollutants Emission Factors- AP42, Fifth Edition” (1995). Available at https://www.epa.gov/air-emissions-factors-and-quantification/ap-42-compilation-air-emission-factors. ———2010. Available and Emerging Technologies for Reducing Greenhouse Gas Emissions from the Petroleum Refining Industry. Research Triangle Park, NC. Available at https://www.epa.gov/sites/production/files/2015-12/documents/refineries.pdf ———“Emissions Estimation Protocol for Petroleum Refineries” ( 2015). Available at https://www3.epa.gov/ttn/chief/efpac/protocol/Protocol%20Report%202015.pdf. U.S. National Fire Protection Association (NFPA). 2003. Code 30: “Flammable and Combustible Liquids.” Quincy, MA: NFPA. Available at http://www.nfpa.org/codes-and-standards/all-codes-and- standards/list-of-codes-and-standards?mode=code&code=30. University of California. 2005. Ernest Orlando Lawrence Berkeley National Laboratory. “Energy Efficiency Improvement and Cost-Saving Opportunities for Petroleum Refineries.” Available at: http://repositories.cdlib.org/cgi/viewcontent.cgi?article=3856&context=lbnl. World Refining Association. 1999. “Efficient Operation of Refineries in Western and Central Europe. Improving Environmental Procedures and Energy Production.” Vienna: Honeywell. 25 ENVIRONMENTAL, HEALTH, AND SAFETY GUIDELINES PETROLEUM REFINING November 17, 2016 ANNEX A. GENERAL DESCRIPTION OF PETROLEUM INDUSTRY ACTIVITIES 74. The EHS Guidelines for Petroleum Refining cover processing operations from crude oil to finished, refined, gaseous, liquid, and solid commercial products and by-products, including refinery fuel gas, liquefied petroleum gas (LPG), motor gasoline (Mo-Gas), kerosene diesel/gasoil, fuel oil, bitumen, asphalt, lubricant oils, waxes, sulfur, pet-coke, and intermediate products for the petrochemical industry (e.g., propane/propylene mixtures, virgin naphtha, aromatics, middle distillates, and vacuum distillates). Finished commercial products are produced from the blending of different intermediate products. These blends are normally referred to as gasoline pool (including cracked naphtha, reformate, isomerate, alkylate, methyl tertiary butyl ether (MTBE), t-amylmethyl ether (TAME), or ethanol, butane, etc.) diesel oil pool, and LPG pool, among others, and have varying compositions, depending on the configuration of the refinery process. 75. Petroleum refineries are complex systems designed specifically to produce the desired products based on the properties of the crude oil feedstock. Refineries may range from medium-integrated refineries to fully integrated refineries (or total conversion refineries), based on the use of different processing units. Modern refineries incorporate different processing units, capable of either high-conversion percentages (coking refineries), medium-conversion (cracking refineries), or low-conversion (hydro-skimming refineries), and are able to process different types of crude oil feed stocks (light, medium, heavy, paraffinic, aromatic, naphthenic (or cyclo-paraffinic)) with differing sulfur content, as in high density, high viscosity, high pour point, etc. An indication of a refinery’s complexity can be assessed with the Nelson Complexity Index (NCI); for instance, an oil refinery with a high NCI (6